Computer Power Configuration

Why this matters

Important

Treat this configuration as a baseline requirement for production performance, not a last-resort troubleshooting step. Start with Required Power/Firmware Settings, then use this page for detailed procedures and validation.

Navigate can drive sustained high data rates (camera readout, storage I/O, network transfer) while also running CPU- and memory-intensive processing. On modern platforms, the host’s power management configuration (Windows power plan, chipset/firmware drivers, and BIOS/UEFI power features) can materially affect throughput, latency, and run-to-run stability.

In our experience, we have seen server-grade, high-performance systems perform surprisingly poorly when configured with power-saving defaults (for example: deep CPU sleep states, package C-states, or aggressive firmware-controlled power management). The symptoms are often subtle: lower-than-expected FPS/throughput, increased jitter, inconsistent job runtimes, and “mystery slowdowns” that disappear after correcting BIOS/OS power settings.

At a high level, the goal is to keep the platform in a deterministic performance state:

• OS power plan prioritizes performance (minimizes power saving).

• Chipset/management drivers are correctly installed (avoids missing firmware interfaces).

• BIOS/UEFI disables deep idle states that add wake-up latency (C-states), while leaving frequency scaling and turbo enabled (P-states + Turbo).

Windows Host Configuration

1. Update baseline software and firmware

1. Ensure the system is on a supported Windows release (Windows 10/11 or Windows Server).

2. Apply your vendor’s recommended BIOS/BMC/firmware updates (Supermicro/HPE/Dell/etc.).

3. Reboot after firmware updates.

2. Set Windows to a performance-focused power mode

Recommended (general): High performance (works broadly). Optional (where available): Ultimate Performance (not present on all editions).

How to set: Control Panel → Power Options → select High performance (or Ultimate Performance).

Additional Windows Settings (AC power): Power Options → Change plan settings → Advanced power settings:

• Processor power management: * Minimum processor state (Plugged in) = 100% * Maximum processor state (Plugged in) = 100%

• PCI Express: * Link State Power Management = Off

3. Install chipset platform drivers (including Intel Management Engine)

The Intel Management Engine (ME) is a chipset subsystem that provides platform management capabilities independent of the OS; the Windows driver typically appears as the Intel Management Engine Interface (MEI) device. Install the correct chipset drivers first, then ME/MEI.

Confirm MEI is installed: Device Manager → System devices → look for Intel(R) Management Engine Interface.

4. Optional Windows Update: CPU/chipset-related driver updates

Windows can deliver additional driver updates through Optional updates. Although it is referred to as “optional”, these updates often include important chipset, storage, and network drivers that improve performance and stability.

How to set: Settings → Windows Update → Advanced options → Optional updates → Driver updates

BIOS/UEFI Configuration

The exact BIOS menu paths vary by vendor and CPU generation, but the concepts are similar.

1. NUMA and Node Interleaving

• Disable Node Interleaving - recommended for modern non-uniform memory access (NUMA)-aware Operating Systems.

Important

Some platforms do not expose an explicit Node Interleaving setting (or it is hidden when the platform defaults to NUMA mode).

2. Power and idle-state controls (C-states, P-states)

How to set: Advanced → Advanced CPU Configuration → Advanced Power Management Configuration

Key settings: * Keep Turbo + P-states enabled (fast frequency scaling). * Disable deep core/package C-states (avoid wake-up latency and jitter). * Disable autonomous hardware power management (keep behavior deterministic).

Recommended BIOS settings

BIOS settings reference (performance mode)

Setting (location)	Recommended	What it does (1 line)
CPU P State Control (APM)
AVX P1	Nominal	Controls the target performance state under heavy AVX; Nominal avoids extra down-binning beyond platform defaults.
SpeedStep (P-states)	Enabled	Enables OS-managed frequency/voltage scaling (fast ramp-up without sleeping).
EIST PSD Function	HW_ALL	Uses hardware assistance for P-state transitions across all cores for responsiveness.
Turbo Mode	Enabled	Allows boosting above base frequency when power/thermals permit.
Hardware PM State Control (APM)
Hardware P-States (HWP)	Disabled	Prevents the CPU from autonomously selecting performance states (keeps policy deterministic).
Autonomous PM	Disabled	Disables out-of-band autonomous power decisions that can introduce variability.
CPU C State Control (APM)
Enable Monitor MWAIT	Disabled	Disables MWAIT-based idle entry hints that can lead to deeper idle behavior.
CPU C1 Auto Demotion	Disabled	Prevents automatic demotion from shallow idle (C1) into deeper C-states.
CPU C6 Report	Disabled	Hides C6 from the OS, preventing deep core sleep selection.
Enhanced Halt State (C1E)	Disabled	Disables C1E voltage/frequency drop behavior that can add wake latency/jitter.
Package C State Control (APM)
Package C State	Disabled	Prevents the entire socket/package from entering deep idle (high wake latency).
Package C State Limit	C0/C1	Caps package idle to shallow states only (best for consistent multi-socket performance).

Validation and Troubleshooting

Generate an energy report (helps spot platform power issues):

powercfg /energy

Verify the active scheme again:

powercfg /getactivescheme

If performance is still lower than expected, re-check:

• BIOS: C-states (core + package) truly disabled / limited to C0/C1.

• Windows: power plan is High/Ultimate Performance and PCIe link state power management is Off.

• Drivers: chipset and MEI installed; vendor storage/NIC drivers installed if required.